Enhancing Thermal Management of InfiniBatt Package by Ansys Simulation Tools

November 2, 2026

Xuan Duan

Table of Contents

Cold weather is tough. Smart engineering is tougher.

Our InfiniBatt study shows how simulation, thermal control, and phase-change materials can help batteries maintain dependable performance in extreme conditions. Read the article and explore the full study.

Introduction

This study uses finite element method (FEM) modeling to improve battery thermal management in extreme cold. By integrating external heating, self-heating, insulation, and a novel sub-zero phase change material (PCM), it efficiently accelerates low-temperature heating. Analyzing variables like ambient and fluctuating temperatures, this approach offers an integrated solution to enhance cold-weather battery performance. Motsai Research’s ‘Infinibatt’ combats cold-climate battery degradation by providing continuous low power (<20W) via a solar-powered, sealed dual-battery pack. An embedded controller efficiently manages internal temperature, solar charging, heating, and wireless communication. Targeting extreme cold, the project uses digital simulations to optimize thermal management, insulation materials, and energy control algorithms for the prototype.

Methodology

The ANSYS Fluent Multi-Scale Multi-Domain (MSMD) model simulates multi-scale lithium-ion battery electrochemical and thermal behavior. It couples internal reactions with Ohmic and reaction heat generation to resolve potential, current density, and temperature distribution[1][2][3].  Using the MSMD module, we simulated a 10Ah, 3.2V flat LiFePO4 battery at a 0.02 C-rate under laminar airflow and forced convection. The model couples governing equations across active (reaction) and passive (tab) components. An initial heater-free simulation established a baseline temperature distribution, while variable initial temperatures allowed us to evaluate thermal performance across different environments.  The numerical model of the battery package is shown in Figure 1. 

Schematic diagram of the Motsai InfiniBatt battery package showing LiFePO4 cells, heater, phase change material (PCM), and tabs for thermal management simulation in R&D
Experimental prototype of the Motsai InfiniBatt thermal management system featuring cylindrical box insulation, air gap, heater, and batteries.

(a)

(b)

Figure 1. Schematic of a) the battery package,  b) the experimental prototype with insulation

To balance accuracy and computational efficiency, a grid independence study was performed in ANSYS Fluent. We evaluated the minimum battery temperatures across various mesh sizes, as outlined in Table 1.

Mesh dependency study results for the Motsai InfiniBatt thermal simulation showing element counts and minimum battery temperatures across three trial numbers in ANSYS Fluent.

The optimal mesh configuration was selected once the temperature differences stabilized within an acceptable range, see Figure 2.

Detailed finite element mesh discretization of the Motsai InfiniBatt battery package generated using ANSYS Fluent for numerical thermal analysis.

Figure 2. Detail of generated mesh for battery package

The ANSYS numerical model—consisting of two prismatic batteries, a heater, and Styrofoam insulation—was validated against a matching physical prototype. To verify its reliability in low-temperature environments, both the simulation and the experiment were tested at an ambient temperature of -19°C with the heater turned off. The simulated temperatures showed good agreement with the experimental data, confirming the model’s accuracy.

Results, Discussion, and Conclusions Summary

This study presents the findings from numerical analyses of battery thermal management strategies designed to prevent excessive temperature drops and ensure reliable operation in extreme cold. The study first investigates the system’s thermal behavior by evaluating the impact of varying initial starting temperatures under identical environmental conditions, alongside an analysis of how real-world daily temperature fluctuations affect overall battery efficiency. Building on these baseline thermal profiles, the study identifies and optimizes the heat flux required to actively maintain a constant battery temperature of 0°C. 

To further enhance passive thermal regulation, a novel design incorporating Phase Change Materials (PCMs) is proposed. By leveraging the gradual heat release of PCMs at specific freezing and melting points, the system effectively prevents the battery from dropping below -10°C. Finally, the conclusions synthesize these findings, providing a comprehensive overview of how initial temperatures, environmental fluctuations, optimized heat flux, and PCM integration collectively contribute to extended battery life and robust thermal management.

References

[1] Y. Huo and Z. Rao, “Investigation of phase change material based battery thermal management at cold temperature using lattice Boltzmann method,” Energy Convers. Manag., vol. 133, pp. 204–215, 2017, doi: 10.1016/j.enconman.2016.12.009.

[2] P. V. Chombo and Y. Laoonual, “A review of safety strategies of a Li-ion battery,” J. Power Sources, vol. 478, no. July, p. 228649, 2020, doi: 10.1016/j.jpowsour.2020.228649.

[3] M. Hussain, M. K. Khan, and M. Pathak, “Thermal management of high-energy lithium titanate oxide batteries using an effective channeled dielectric fluid immersion cooling system,” Energy Convers. Manag., vol. 313, no. February, p. 118644, 2024, doi: 10.1016/j.enconman.2024.118644.

Share this article

Recent News

Circuit Design for De-passivation for a Long Term Storage Battery

A battery can appear fully charged after long-term storage—yet still struggle to deliver the power a device needs at start-up....

Embedded AI for IoT Devices: Simplified Insights from a Concordia Study

Embedded AI enables IoT devices to process data locally, improving speed, security, and energy efficiency while reducing reliance on cloud...

Motsai at Hannover Messe 2026

Motsai joins Hannover Messe 2026 at the Canada Pavilion with NGen. Discover how we accelerate innovative product development. Let’s connect....